Cast Iron Body
Suits most flange bolt patterns including, Table D/E, PN10-16 & ANSI 150
PCD is measured from a range of smallest to largest PCD measured with Table D/E, PN10-16 & ANSI 150
EPDM seat (Temperature rating -20°C, +120°C)
Resilient Seated
Nominal Pressure - 1.6 Mpa (16 bar)
Aluminium handle with ten position stainless steel notch plate (SS304)
CF8M disc (SS316)
Epoxy resin powder paint according to ISO 21809
BSP threaded ends
Maximum pressure 1000PSI / 69Bar W.O.G. (Water, Oil, Gas)
PTFE seal maximum temperature 160°C
... Full port
Lockable latch handle
Red handle sleeve available for hot water indication
Bolt Kit to suit bolting a Table E Flange to one side of a Table E Lugged Butterfly Valve.
For Kit contents, click View Dimensions
A: Bolts... B: Flat Washers
Sizes DN40-DN300 are Cast Iron, Sizes DN350-DN400 are Ductile Iron
Table D/E threaded bolt pattern (metric)
EPDM seat (Temperature rating -20°C, +120°C)
... Resilient Seated
Nominal Pressure - 1.6 Mpa (16 bar)
Aluminium handle with ten position stainless steel notch plate (SS304)
CF8M disc (SS316)
Epoxy resin powder paint according to ISO 21809
For sizes DN250+, it is recommended to use with a gearbox for manual operation (kits available for purchase)
Butt welds to Outside Diameter tube sizes
EPDM seal (Food Grade) maximum temperature 120°C
Centre clamp for easy access
... Spring actioned flow control
BSP threaded ends
PTFE seal maximum temperature rating 200°C
Maximum pressure 6000PSI / 400Bar
... T handle operation
'B' Measurement is taken when the valve is fully open and the handle is at it's highest point
BSP threaded ends
Maximum pressure 230PSI / 16Bar
Stainless steel body and gate
... Aluminium handwheel
No seal
These are an Isolation valve, not a full Termination valve due to having no seal/gasket
Butt welds to Outside Diameter tube sizes
Maximum pressure 145PSI / 10Bar
Maximum working temperature 150°C (with silicone seal)
... Multi-position trigger handle
Parts are interchangeable with Keystone F250 valves
Butt welds to Outside Diameter tube sizes
Maximum pressure 145PSI / 10Bar
Maximum working temperature 110°C (with EPDM seal)
... Multi-position handle
Stainless steel trigger handle available
RJT Male to RJT Female connection
Maximum pressure 145PSI / 10Bar
Maximum working temperature 110°C (with EPDM seal)
... Multi-position handle
Stainless steel trigger handle available
BSP threaded ends
Maximum pressure 1000PSI / 69Bar W.O.G. (Water, Oil, Gas)
PTFE seal maximum temperature 160°C
... Full port
Lockable latch handle
Red handle sleeve available for hot water indication
BSP threaded ends
Maximum pressure 230PSI / 16Bar
No seal
... Stainless steel body and disc
Please note that these only operate in a vertical orientation
Bolt Kit to suit bolting a Table D Flange to one side of a Table E Lugged Butterfly Valve.
For Kit contents, click View Dimensions
A: Bolts... B: Flat Washers
BSP threaded ends
Maximum pressure 230PSI / 16Bar
Stainless steel body and gate
... Aluminium handwheel
No seal
These are an Isolation valve, not a full Termination valve due to having no seal/gasket
RJT Male/Female connections
EPDM seal (Food Grade) maximum temperature 120°C
Centre clamp for easy access
... Spring actioned flow control
Flow direction is from RJT female to RJT male
RJT Male to RJT Female connection
Maximum pressure 145PSI / 10Bar
Maximum working temperature 150°C (with silicone seal)
... Multi-position trigger handle
Parts are interchangeable with Keystone F250 valves
Tri Clover Ferrule connections
Maximum pressure 145PSI / 10Bar
Maximum working temperature 110°C (with EPDM seal)
... Multi-position handle
Stainless steel trigger handle available
BSP threaded ends
Maximum pressure 230PSI / 16Bar
No seal
... Stainless steel body and disc
Retaining Pin for Disc Alignment
Can be used in a vertical or horizontal orientation
Bolt Kit to suit bolting a PN10-16 Flange to one side of a PN10-16 Lugged Butterfly Valve.
For Kit contents, click View Dimensions
A: Bolts... B: Flat Washers
Tri Clover Ferrule connection
Maximum pressure 145PSI / 10Bar
Maximum working temperature 150°C (with silicone seal)
... Multi-position trigger handle
Parts are interchangeable with Keystone F250 valves
BSP threaded ends
Maximum pressure 580PSI / 40Bar
No seal
... Stainless steel body and disc
No Retaining Pin for Disc Alignment
Can only be used in a vertical orientation
Bolt Kit to suit bolting a ANSI150 Flange to one side of a ANSI150 Lugged Butterfly Valve.
For Kit contents, click View Dimensions
A: Bolts... B: Flat Washers
Cast Iron Body
Suits most flange bolt patterns including, Table D/E, PN10-16 & ANSI 150
PCD is measured from a range of smallest to largest PCD measured with Table D/E, PN10-16 & ANSI 150
... EPDM seat (Temperature rating -20°C, +120°C)
Resilient Seated
Nominal Pressure - 1.6 Mpa (16 bar)
Aluminium handle with ten position stainless steel notch plate (SS304)
CF8M disc (SS316)
Epoxy resin powder paint according to ISO 21809
EPDM Seals
RapidPress Coupler Connections
Full Port
... Lockable latch handle
Temperature Rating: -20°C, 120°C
Red handle sleeves available for purchase
RapidPress Extreme options available
**Please note: 76.1x65NB has been fabricated from a standard 65NB BSP Ball Valve and two 76.1 RapidPress Weld Couplers**
Able to be clamped in centre of union for easy access
Maximum pressure 145PSI / 10Bar
Maximum working temperature 120°C (with EPDM seal)
... Spring actioned flow control
Can be used with Tri Clover and RJT unions
Bolt Kit to suit bolting two Table E Flanges together with a Wafer Butterfly Valve in between.
For Kit contents, click View Dimensions
A: Bolts... B: Hex Nuts C: Flat Washers
BSP threaded ends
Maximum pressure 1000PSI / 69Bar W.O.G. (Water, Oil, Gas)
PTFE seal maximum temperature 250°C
... Lockable latch handle
ISO5211 mounting pad - These do not fit to actuators but can be used for mounting to wall or panels
Reduced port
3 way valves from 2 1/2" to 4" will differ from image shown
Bolt Kit to suit bolting two Table D Flanges together with a Wafer Butterfly Valve in between.
For Kit contents, click View Dimensions
A: Bolts... B: Hex Nuts C: Flat Washers
BSP threaded ends
Maximum pressure 1000PSI / 69Bar W.O.G. (Water, Oil, Gas)
PTFE seal maximum temperature 250°C
... Lockable latch handle
ISO5211 mounting pad - These do not fit to actuators but can be used for mounting to wall or panels
Reduced port
3 way valves from 2 1/2" to 4" will differ from image shown
Bolt Kit to suit bolting two PN10-40 Flanges together with a Wafer Butterfly Valve in between.
For Kit contents, click View Dimensions
A: Bolts
... B: Hex Nuts
C: Flat Washers
Cast Iron Body
Suitable for use with all flanges, including Table D/E, PN10-16 & ANSI 150
EPDM seat (Temperature rating -20°C, +120°C)
... Resilient Seated
Nominal Pressure - 1.6 Mpa (16 bar)
CF8M disc (SS316)
Epoxy resin powder paint according to ISO 21809
Bolt Kit to suit bolting two ANSI150 Flanges together with a Wafer Butterfly Valve in between.
For Kit contents, click View Dimensions
A: Bolts... B: Hex Nuts C: Flat Washers
Bolt Kit to suit bolting two Table E Flanges together with a Wafer Check Valve in between.
For Kit contents, click View Dimensions
A: Bolts
... B: Hex Nuts
C: Flat Washers
Ductile Iron Body
Table E bolt pattern
Nominal Pressure - 1.6 Mpa (16 bar)
... Drain Plug on Cover
Graphite Cover Gasket
Graphite temperature rating -10°C to 230°C
Epoxy resin powder paint according to ISO 21809
Bolt Kit to suit bolting two Table D Flanges together with a Wafer Check Valve in between.
For Kit contents, click View Dimensions
A: Bolts
... B: Hex Nuts
C: Flat Washers
Bolt Kit to suit bolting two PN10-40 Flanges together with a Wafer Check Valve in between.
For Kit contents, click View Dimensions
A: Bolts
... B: Hex Nuts
C: Flat Washers
Bolt Kit to suit bolting two ANSI150 Flanges together with a Wafer Check Valve in between.
For Kit contents, click View Dimensions
A: Bolts
... B: Hex Nuts
C: Flat Washers
Bolt Kit to suit bolting two ANSI300 Flanges together with a Wafer Check Valve in between.
For Kit contents, click View Dimensions
A: Bolts
... B: Hex Nuts
C: Flat Washers
Bolt Kit to suit bolting two AS4087 Flanges together with a Wafer Check Valve in between.
For Kit contents, click View Dimensions
A: Bolts
... B: Hex Nuts
C: Flat Washers
Bolt Kit to suit bolting a Table E Flange to one side of a Table E Y Strainer.
For Kit contents, click View Dimensions
A: Bolts... B: Hex Nuts C: Flat Washers
Bolt Kit to suit bolting a PN10-40 Flange to one side of a PN16 Isolating Regulating Valve.
For Kit contents, click View Dimensions
A: Bolts... B: Hex Nuts C: Flat Washers
Bolt Kit to suit bolting a Table E Flange to one side of a Table E Expansion Bellow.
For Kit contents, click View Dimensions
A: Bolts
... B: Hex Nuts
C: Flat Washers
